![]() ![]() You need to contact a customer service representative to arrange for a Return Merchandise Authorization form No returns without prior authorization from the Supplier (see Contact Us page). Note all returns and cancellations require a prior authorization.Īll returns and cancellations may be subject to shipping charges, unless caused by our error or cancelled by the customer prior to shipping. You can return or cancel your order by contacting our customer service desk. If a part is defective, we will replace it 100% FREE. It typically takes us approximately 3-5 business days to process a credit back to your account and 2-3 business days for the credit to appear on your account. You may return any item in its original condition for a full refund within 30 days of receipt of your shipment, less shipping charges. after 12k miles of use from initial purchase.installed heat tab is melted, removed, or modified.failure is due to vehicle use other than as intended or recommended by manufacturer.part is installed or operated outside the US.failure of part is due to collision damage.vehicle is converted from private passenger use to commercial, fleet, racing, or other competitive on/off-road recreational settings.damage is due to misuse, abuse, or modification.Though additional parts and accessories may be attached upon purchase, coverage does not extend to sensors, switches, cables, electronics, belts, hoses, water pumps, or manifolds, nor damage caused through overheating or improper lubrication. Claims on engine warranties are limited to manufacturer defects in the pistons, heads, block, crankshafts, rockers, and oil pumps. All of our engines and transmissions carry a 1-year warranty with optional extensions up to 1 additional year. Please note that the tool that you receive after placing an online order may be in a used but operable condition due to the nature of the Loan-A-Tool® program.We offer an industry leading 1-year warranty on every part type we sell. Do not wear ties or loose clothing when working on your vehicle.įREE Loan-A-Tool® program requires returnable deposit. Should electrolyte get on your body or clothing, neutralize it immediately with a solution of baking soda and water. Always wear gloves and safety glasses and other personal protection equipment, and work in a well-ventilated area. Sulfuric acid is caustic and can burn clothing and skin or cause blindness. Use caution when working with automotive batteries. ![]() Always disconnect the negative battery cable before servicing an electrical application on the vehicle to protect its electrical circuits in the event that a wire is accidentally pierced or grounded. Always chock your wheels prior to lifting a vehicle. Refer to the service manual for specific diagnostic, repair and tool information for your particular vehicle. Information is accurate and true to the best of AutoZone’s knowledge, however, there may be omissions, errors or mistakes.īe sure to consult your owner’s manual, a repair guide, an AutoZoner at a store near you, or a licensed, professional mechanic for vehicle-specific repair information. Example of this install at 6:21 in the video.Īdvice, how-to guides, and car care information featured on and AutoZone Advice & How-To’s are presented as helpful resources for general maintenance and automotive repairs from a general perspective only and should be used at your own risk. If that’s the case, just remove what you need to, change the bulb, and put back what you removed. Occasionally you will have to remove something, in the video it’s an air filter housing but in other vehicles it may be a coolant reservoir or a battery, to get to one or more of the bulbs. Some casings don’t remove easily, but, with the hood up, you can reach behind the casing and access the bulb. ![]() You may need some tools to pull the wheel arch back to get to the bulb, remove and replace it, and then reinstall the wheel well cover. Other bulbs can only be accessed by going through the wheel well. Example of this at 2:06 in the video on the top of the page. Some headlights are stored in removable, easy-to-access assemblies that usually come out after removing a few screws.Take those out, and you can lay the headlight assembly onto the fascia to reach the bulbs. This is where you’ll run into the most variance. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |